This is what I set up for backups recently using a cheap USB-enclosure which can house 2 SATA disks and shows them as 2 USB mass-storage devices to my system (using only one USB cable). Without any further introduction, here goes the HOWTO:
First, create one big partition on each of the two disks (/dev/sdc and /dev/sdd in my case) of the exact same size. The cfdisk details are omitted here.
$ cfdisk /dev/sdc $ cfdisk /dev/sdd
Then, create a new RAID array using the mdadm utility:
$ mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sdc1 /dev/sdd1
The array is named md0, consists of the two devices (--raid-devices=2) /dev/sdc1 and /dev/sdd1, and it's a RAID-1 array, i.e. data is simply mirrored on both disks so if one of them fails you don't lose data (--level=1). After this has been done the array will be synchronized so that both disks contain the same data (this process will take a long time). You can watch the current status via:
$ cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdd1 sdc1 1465135869 blocks super 1.1 [2/2] [UU] [>....................] resync = 0.0% (70016/1465135869) finish=2440.6min speed=10002K/sec unused devices:
Some more info is also available from mdadm:
$ mdadm --detail --scan ARRAY /dev/md0 metadata=1.01 name=foobar:0 UUID=1234578:1234578:1234578:1234578 $ mdadm --detail /dev/md0 /dev/md0: Version : 1.01 Creation Time : Sat Feb 6 23:58:51 2010 Raid Level : raid1 Array Size : 1465135869 (1397.26 GiB 1500.30 GB) Used Dev Size : 1465135869 (1397.26 GiB 1500.30 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Update Time : Sun Feb 7 00:03:21 2010 State : active, resyncing Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Rebuild Status : 0% complete Name : foobar:0 (local to host foobar) UUID : 1234578:1234578:1234578:1234578 Events : 1 Number Major Minor RaidDevice State 0 8 33 0 active sync /dev/sdc1 1 8 49 1 active sync /dev/sdd1
Next, you'll want to create a big partition on the RAID device (cfdisk details omitted)...
$ cfdisk /dev/md0
...and then encrypt all the (future) data on the device using dm-crypt+LUKS and cryptsetup:
$ cryptsetup --verbose --verify-passphrase luksFormat /dev/md0p1 Enter your desired pasphrase here (twice) $ cryptsetup luksOpen /dev/md0p1 myraid
After opening the encrypted container with cryptsetup luksOpen you can create a filesystem on it (ext3 in my case):
$ mkfs.ext3 -j -m 0 /dev/mapper/myraid
That's about it. In future you can access the RAID data by using the steps below.
Starting the RAID and mouting the drive:
$ mdadm --assemble /dev/md0 /dev/sdc1 /dev/sdd1 $ cryptsetup luksOpen /dev/md0p1 myraid $ mount -t ext3 /dev/mapper/myraid /mnt
Shutting down the RAID:
$ umount /mnt $ cryptsetup luksClose myraid $ mdadm --stop /dev/md0
That's all. Performance is shitty due to all the data being shoved out over one USB cable (and USB itself being too slow for these amounts of data), but I don't care too much about that as this setup is meant for backups, not performance-critical stuff.
Update 04/2011: Thanks to Bohdan Zograf there's a Belorussian translation of this article now!
I recently almost died from a heart attack because after a really horrible crash (don't ask), Debian unstable on my laptop wouldn't boot anymore. The system hung at "Waiting for root filesystem...", and I was in panic mode as I feared I lost all my data (and as usual my backups were waaay too old).
At first I was suspecting that something actually got erased or mangled due to the crash, either at the dm-crypt layer, or the LVM layer, or the ext3 filesystem on top of those. After various hours of messing with live CDs, cryptsetup, lvm commands (such as pvscan, pvs, vgchange, vgs, vgck) and finally fsck I still had not managed to successfully boot my laptop.
I finally was able to boot by changing the initrd from initrd.img-2.6.30-2-686 to initrd.img-2.6.30-2-686.bak in the GRUB2 menu (at boot-time), at which point it was clear that something was wrong with my current initrd. A bit of debugging and some initrd comparisons revealed the cause:
Both, the cryptsetup and lvm2 packages were no longer installed on my laptop, which made all update-initramfs invokations (e.g. upon kernel package updates) create initrds which did not contain the proper dm-crypt and lvm functionality support. Hence, no booting for me. I only noticed because of the crash, as I usually do not reboot the laptop very often (two or three times per year maybe).
Now, as to why those packages were removed I have absolutely no idea. I did not remove them knowingly, so I suspect some dist-upgrade did it and I didn't notice (but I do carefully check which packages dist-upgrade tries to remove, usually)...
Here's a nice opportunity for everyone to learn more about coreboot, a Free Software / Open Source firmware/BIOS for x86 PCs.
Ron Minnich, founder of the LinuxBIOS (now called coreboot) project, Peter Stuge of Stuge Konsult, and Stefan Reinauer of coresystems GmbH have given a presentation for the Google Tech Talks series recently. The topic was (of course) coreboot, its history, goals, features and technical details, surrounding tools and libraries such as flashrom and libpayload, as well as an automated test system for running a hardware test-suite upon every checkin in the coreboot repository.
A video of the talk, aptly named coreboot (aka LinuxBIOS): The Free/Open-Source x86 Firmware (134 MB), is available from Youtube, get it for instance via:
$ apt-get install youtube-dl $ youtube-dl http://www.youtube.com/watch?v=X72LgcMpM9k
The talk includes various demos of coreboot and various payloads you can use with coreboot. One nice example is the TINT payload, a Tetris-like game for Linux (
apt-get install tint for the curious), which has been reworked to be usable as a coreboot payload.
So, yes, you can now put Tetris in your BIOS ROM chip and play it from there (no hard drive required).
Other demos included some cluster nodes with coreboot, and a "normal" x86 desktop board booting coreboot + Linux in a very few seconds (much room left for optimizing there though, if you really want to get into fast booting).
Check out the full talk for more infos, and if you're willing to give it a try (see the list of currently supported boards), contact us on the mailing list or join the #coreboot IRC channel on Freenode.
Fun stuff I just stumbled over: a personal/human airbag from Japan, supposedly meant for elderly people who might fall and injure themselves.
Watch a video of the airbag in action on Youtube (no need for crappy Flash player, you can use youtube-dl for instance). Such a device could be a lot of fun I imagine; make it cheap enough and lots of people will buy it just for fun falling-on-your-back experiments :-)
...next time you write such a piece of malware, how about making it do something useful (instead of nefarious) for a change, say, have your botnet zombies become Tor exit nodes? kthxbye.